VBA-4E3A-KE-ZEJQ/E2L
25957 ₽
Параметры
| Входы питания | Внутренний (от AS-i) |
|---|---|
| Выходы питания | Внешний (от AUX) |
| Выходы модуля | 3 |
| Стиль корпуса | KE |
| Место монтажа | Монтаж в корпус |
| Входы модуля | 4 |
| Тип модуля | Цифровые I/O |
| Подключение I/O | Клеммники |
| Тип узла | A/B узел |
Технические характеристики
The AS-Interface I/O module VBA-4E4A-KE-ZEJQ/E2L is a control cabinet module with 4 inputs and 3 electronic outputs.
The housing is only 22.5 mm wide and takes up little space in the control cabinet. The module is mounted by snapping onto the 35-mm DIN rail in compliance with EN 50022.
The connection is made via plug-in terminals. Four-terminal blocks (black) are used for the inputs. The connection of the outputs, the external bulk power and the AS-Interface is via 2-terminal blocks (output black, bulk power grey, AS-Interface yellow).
The supply to the inputs and the connected sensors can be fed either from the internal supply of the module (from the AS-Interface) or via an external voltage source.
A switch located on the side of the module changes the supply source. The choice of internal input supply is displayed via the INT LED.
The IN and OUT LEDs display the current switching status of the relevant inputs and outputs. The OUT LED also indicates an overload or a lead breakage at the associated output.
Note:
The device is equipped with a communication monitor, which deactivates the outputs if the AS-Interface does not communicate with the module for more than 40 ms.
The communication monitor can be deactivated via the parameter P0.
Filters that suppress pulses with a duration of 2 ms or less at the inputs can be connected via the parameter P1.
Parameter P2 activates a lead breakage detection system for the outputs. This function detects and reports a missing load, providing the relevant output is deactivated. The associated OUT LED and the «peripheral fault» function display the signal transmitted to the AS-Interface master.
A signal indicating an overload of the internal input supply or the outputs is also transmitted to the AS-Interface master via the «peripheral fault» function. Communication via the AS-Interface continues even if a peripheral fault is set.
| Описание продукта |
|---|
| Модуль распределительного шкафа KE, 4 входа и 3 выхода |
| Основные Характеристики | ||
|---|---|---|
| Node type | Узел A/B | |
| Спецификация AS-интерфейса | В3.0 | |
| Требуемая спецификация шлюза | ≥ V2.1 | |
| Профиль | Профиль | |
| Код ввода-вывода | 7 | |
| Код ID | A | |
| Код ID1 | 7 | |
| Код ID2 | 0 | |
| UL File Number | E223772 | |
| Индикаторы/средства управления | ||
| СВЕТОДИОДНАЯ НЕИСПРАВНОСТЬ | Error display; red LED red: communication error, i.e. address is 0 red flashing: overload internal input supply, i.e. overload or lead interruption outputs |
|
| СВЕТОДИОД ВНУТРЕННИЙ | Внутреннее входное питание активно; светодиод зелёный. | |
| LED PWR | AS-Interface voltage; green LED green: voltage OK flashing green: address 0 |
|
| Светодиод AUX | ext. auxiliary voltage UAUX; dual LED green/red green: voltage OK red: reverse voltage |
|
| LED IN | Состояние переключения (вход); 4 светодиода жёлтого цвета | |
| LED OUT | Switching state (output); 3 LED yellow/red yellow: Output active red: Output overload or lead breakage |
|
| Электрические характеристики | ||
| Вспомогательное напряжение (вход) | 12 … 30 В DC PELV | |
| Вспомогательное напряжение (выход) | 20 … 30 В DC PELV | |
| Номинальное рабочее напряжение | 26,5 … 31,6 В от AS-Interface | |
| Номинальный рабочий ток | ≤ 35 мА (без датчиков) / макс. 190 мА | |
| Класс защиты | Класс защиты | |
| Защита от перегрузки | UEXT, UAUX, Ue: Over voltage category III, safe isolated power supplies (PELV) | |
| Вход | ||
| Номер/Тип | 4 входа для 2- или 3-проводных датчиков (PNP), DC | |
| Питание | from AS-Interface (switch position INT, default settings) or external UEXT (switch position EXT) | |
| Напряжение | 21 … 31 В DC (INT) | |
| Текущая нагрузочная способность | ≤ 150 мА, с защитой от перегрузки и короткого замыкания (INT) | |
| Входной ток | ≤ 9 мА (ограничено внутренне) | |
| Точка переключения | в соответствии с DIN EN 61131-2 (Тип 2) | |
| 0 (неослабленный) | ≤ 3 мА | |
| 1 (ослабленный) | ≥ 5 мА | |
| Задержка сигнала | < 1 мс (вход/AS-Interface) | |
| Выход | ||
| Номер/Тип | 3 электронных выхода, PNP, защищены от перегрузки и короткого замыкания | |
| Питание | from external auxiliary voltage UAUX | |
| Напряжение | ≥ (UAUX — 0.5 V) | |
| Ток | O1 max. 3 A, O2/O3 max. 1.5 A, total 6 A (TB ≤ 40 °C) O1 max. 2 A, O2/O3 max. 1 A, total 4 A (TB ≤ 60 °C) |
|
| Категория использования | DC-13 | |
| Соответствие директивам | ||
| Электромагнитная совместимость | ||
| Directive 2014/30/EU | EN 62026-2:2013 EN 61000-6-2:2005, EN 61000-6-4:2007 | |
| Стандарты соответствия | ||
| Степень защиты | EN 60529:2000 | |
| Стандарт Fieldbus | EN 62026-2:2013 | |
| Вход | EN 61131-2:2004 | |
| Излучаемые помехи | EN 61000-6-4:2007 | |
| AS-Интерфейс | EN 62026-2:2013 | |
| Помехоустойчивость | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 | |
| Условия окружающей среды | ||
| Температура окружающей среды | -25 … 60 °C (-13 … 140 °F) | |
| Температура хранения | -25 … 85 °C (-13 … 185 °F) | |
| Относительная влажность | 85 %, без конденсации | |
| Климатические условия | Только для использования в помещении. | |
| Высота | ≤ 2000 м над уровнем моря | |
| Степень загрязнения | 2 | |
| Механические характеристики | ||
| Степень защиты | IP20 | |
| Связь | removable terminals rated connection capacity: rigid/flexible (with and without wire-end ferrules): 0.25 mm2 … 2.5 mm2 for multiple-wire connection with two wires of equal cross-section: flexible with twin wire-end ferrules: 0.5 mm2 … 1.5 mm2 |
|
| Материал | ||
| Корпус | PA 66-FR | |
| Масса | 150 г | |
| Размеры | ||
| Высота | 99 мм | |
| Ширина | 22,5 мм | |
| Длина | 102 мм | |
| Монтаж | DIN-рейка для монтажа | |
| Момент затяжки зажимных винтов | 0,5 Н·м … 0,6 Н·м | |
